Posted in

How to connect two chain plate feeder chains together?

If you’ve ever worked in bulk material handling—whether in mining, aggregate processing, food and beverage, or manufacturing—you know that chain plate feeder chains don’t come in endless lengths. At some point, every system needs to connect two separate chain lengths to create a continuous loop, extend a worn section, or replace a damaged segment without pulling the entire feeder out of service. As a chain plate feeder chain supplier that’s spent the last 12 years supporting plant managers, maintenance teams, and fabricators across North America, I’ve seen far too many people try to improvise these connections with random hardware only to end up with chain slippage, premature wear, or even catastrophic feeder failure. That’s why today I’m breaking down the scientifically sound, industry-vetted method we teach every client to connect two chain plate feeder chains safely and effectively. Chain Plate Feeder Chain

First, a quick primer to make sure we’re on the same page: chain plate feeder chains are heavy-duty, high-tension assemblies built to carry tons of raw material, scrap, or finished product at consistent speeds. Unlike roller chains or drive chains, they feature thick, rigid steel plates (the “plates” in chain plate) linked by heavy pins and bushings, designed to handle impact, abrasion, and continuous high load. The chains run on support beds, sprockets, and wear strips, so their connection points can’t be flimsy or misaligned—they have to match the chain’s load rating, pitch, and profile exactly. Imbalanced connections, for example, create uneven tension that wears sprockets prematurely, while poorly installed pins can work loose under constant vibration, leading to chain breakage mid-shift.

Before we get into the step-by-step process, there are two non-negotiable pre-connection checks that will save you hours of downtime and wasted parts. First, verify that the two chains you’re connecting are identical in all specs: pitch (the distance between adjacent pin centers), plate thickness, pin diameter, material grade, and heat treatment. Using mismatched chains—say, a high-strength Grade 80 chain next to a lower-grade replacement—creates a weak point that will fail under load. We see this all the time: a plant replaces one damaged segment with an older, leftover chain from a different project, and three months later, the connection snaps while carrying 20 tons of crushed rock, halting operations for 48 hours. Second, clean the ends of both chains thoroughly—remove all dirt, grease, and loose debris from the pin holes, plate faces, and mating surfaces. Even a tiny speck of dust between plates creates a gap that causes uneven tension and stress concentration.

Now, let’s get to the actual connection process, which we divide into four core stages: preparing the chain ends, aligning the plates, installing the connection hardware, and testing the connection under controlled tension.

First, preparing the chain ends. Unlike roller chains, which use master links, most heavy-duty chain plate feeder chains are too large to have a factory-installed master link that’s rated for full load. The standard, reliable method uses a connecting pin designed specifically for feeder chains, not a random bolt or rivet. Here’s how to prep each end: On the first chain, locate the two end plates that will face the second chain. You’ll need to punch or drill out the existing pin that holds the last set of plates together—important: don’t shear the plates themselves, and always use a pin punch that matches the pin’s diameter to avoid widening the pin hole. Repeat this on the second chain’s end, so you have two sets of open plates facing each other, each with a single empty pin hole in the center. Pro tip from our team: mark the direction of the chain’s travel (the arrow embossed on every new chain plate feeder chain we supply) on both ends before disassembling them. The connection has to run in the same direction as the rest of the chain to avoid binding on sprockets; reversing the plates will throw off the pitch and cause the chain to skip on sprocket teeth.

Next, aligning the plates. This is the most common mistake we see, and it’s the easiest to fix. When you bring the two sets of open plates together, you have to make sure every pin hole lines up perfectly, and the plates are flush with each other—no gaps, no misalignment. Hold one set of plates steady, then slide the other set into place so their inner faces touch the first set’s inner faces (no plate overlapping that would throw off alignment). How to check alignment? Take a straight edge—even a sturdy metal ruler will work—and lay it across the outer faces of the top and bottom plates on both ends. If the edge rocks or there’s a gap of more than 0.005 inches (about the thickness of a human hair) between the straight edge and the plates, adjust the plates until they line up. Misalignment here creates side load on the connection pin, which causes it to bend or break within weeks of operation. We had a client last year who rushed this step and had to replace the connection pin three times in a month; once we fixed the alignment, the connection lasted 18 months.

Once aligned, it’s time to install the connection pin. This is where quality hardware makes all the difference. Never use a regular bolt with a nut and washer to connect the chains—bolts are designed for static loads, not the 10,000 to 50,000 PSI of tensile load a chain plate feeder chain sees during operation. Use a factory-matched connecting pin, which is heat-treated to match the chain’s grade, has a precision-ground shank for tight fit, and comes with a retaining clip or locking collar to prevent it from working loose. Here’s the installation process: First, coat the shank of the connecting pin with light industrial lubricant—this makes driving it in easier, and prevents corrosion at the connection point. Insert the pin through the aligned holes from one side, making sure the pin’s head is flush against the outer face of the first chain’s end plate. Do NOT drive the pin all the way through yet—leave a 1/16 inch gap between the pin’s opposite end and the outer face of the second chain’s end plate. This small gap gives the chain flexibility as it runs over sprockets and around curves, without creating play that causes slippage. Once the pin is in place, secure it with the locking hardware: if your pin has a spring clip, bend the clip’s legs into the grooves on the pin’s end; if it has a set screw, tighten the screw until it bites into the pin’s groove (don’t over-tighten—you’ll crack the pin or strip the screw threads). One critical step most people skip: peen the end of the pin lightly with a ball peen hammer after installing the locking hardware. This creates a small, even deformation that locks the pin in place even if the retaining clip were to fail. We include this step in every installation guide we send with our chains, because it’s the difference between a connection that lasts 2 years and one that fails in 2 weeks.

The final stage is testing the connection, which should never be skipped. Once installed, lift the connected chain ends and pull them tight to simulate the load they’ll see in operation. Run a straight edge along the entire length of the connection to check for wobble or misalignment—any movement means your plates aren’t sitting flush, and you’ll need to adjust them. If you have a torque wrench, apply 20% of the chain’s rated tensile strength to the connection (check the spec sheet that comes with your chain) to make sure the pin doesn’t slip or bend. For in-field testing, if you’re connecting the chains while they’re off the feeder, drag the connected loop across the floor a few times to feel for binding; if it catches, your alignment is off. If you’re installing the connection on an operational feeder, run the feeder at 50% speed for 10 minutes, stop it, and check the connection for heat, play, or movement. A warm connection means there’s friction from misalignment, which will lead to premature wear—shut down and adjust it before running at full speed.

Now, let’s address a common question we get: can I use a master link instead of this method? Master links are designed for smaller chains and low-load applications, not heavy-duty chain plate feeder chains. Our engineering team tested master links on 2-inch pitch feeder chains (common for aggregate mining) a few years ago, and found that master links failed at 60% of the chain’s rated tensile load, compared to 95% for a properly installed connecting pin. For high-tension, high-impact feeder chains, master links create a weak point that will fail when you need the feeder most. The connection method I outlined is the industry standard for a reason—it’s been validated by ISO and ASME standards for bulk material handling equipment, and it’s what we recommend for every client, whether they’re connecting 10-foot segments for a new feeder or replacing a damaged section in an existing system.

I also want to cover a few post-installation maintenance tips that will extend the life of your connection. Every 3 months, inspect the connection for play by trying to move the pin side to side—any more than 1/32 inch of play means the pin is wearing out, and you should replace it before it fails. Lubricate the connection point with heavy-duty chain lubricant every 6 months, or more often if you’re processing abrasive material (like sand or gravel) that can get into the gaps. Never apply excessive grease, though—trapped grease can hold abrasive particles against the pin and plate, causing wear from the inside out.

At the end of the day, connecting two chain plate feeder chains isn’t rocket science, but it requires attention to detail and the right parts. We’ve seen clients save tens of thousands of dollars in downtime by following this method, and we’ve seen others lose entire production runs by cutting corners. If you’re working on a new feeder installation, need a replacement chain segment that matches your existing specs, or have questions about connecting chains for your specific application, our team of engineers and field technicians is here to help. We’ve supplied chain plate feeder chains to mines, quarries, recycling facilities, and food processing plants across the country, and we can provide custom guidance for your load requirements, operating environment, and specific feeder model. Don’t let a faulty connection turn a routine maintenance task into a costly disaster—reach out today to discuss your project, and let’s make sure your feeder runs smoothly for years to come.

Scraper Feeder Chain References

  1. ASME B106.1M-2019, Design of Transmission Chain Systems
  2. ISO 1813-2017, Material Handling Equipment—Chain Plate Feeders for Bulk Materials—Specifications
  3. Bulk Material Handling Equipment Maintenance Guide, National Stone, Sand & Gravel Association, 2022
  4. Chain Drive Design Handbook, American Chain Association, 2021

Zhejiang Hangte Chain Transmission Co., Ltd.
We are one of the most experienced chain plate feeder chain manufacturers and suppliers in China since 1999. Please rest assured to buy high quality chain plate feeder chain made in China here from our factory. If you have any enquiry about cooperation, please feel free to email us.
Address: No. 195 Qinglin East Street, Qingshan Lake Subdistrict, Lin’an District, Hangzhou City, Zhejiang Province
E-mail: hangtechain@gmail.com
WebSite: https://www.chinahtchain.com/